Home > Radon Detectors > Radstar RS300 Continuous Radon Gas Monitor & Detector for Home Inspectors & Radon Testing Professionals

Radstar RS300 Continuous Radon Gas Monitor & Detector for Home Inspectors & Radon Testing Professionals

Radstar RS300 Continuous Radon Gas Monitor & Detector for Home Inspectors & Radon Testing Professionals
Item# RS300
$999.95
Your Price: $819.95
Availability: Usually ships the next business day.

Product Description

The U.S. Environmental Protection Agency (EPA) has verified this product for accurate radon measurement. NEHA & NRPP listed. This product is made in the USA!

Free Shipping on this item.

This IS NOT a digital read-out display device and is for printed reports only.

Reports Radon Gas Levels in as little as 4 hours and continues to read every hour and report average reading. Features NICAD rechargeable batteries. Very light and compact with carrying handle. Comes with easy to install CD software and USB cable to connect to your PC or Laptop (Windows Only Compatible) and print reports. Motion Senor and Key Lock to prevent tampering. Will continue to read up to 10 days. (Note: The EPA considers any reading under 48 hours to be invalid.)

  • Accurate measurements in a wide range of temperatures and humidity
  • Temperature Operating Range: 50 to 90 Degrees Fahrenheit
  • Humidity Operating Range: 0 to 80% Relative Humidity (Non-Condensing)
  • Internal memory
  • Software CD Download to your Laptop or PC (Windows Only) and print reports
  • Lightweight, durable and tamper-resistant
  • Continuous measurement of radon gas - Provides hourly and average readings
  • Use AC power or built in rechargeable NICAD batteries -Unaffected by power surges or fluctuations
  • Accurate measurements in a wide range of temperatures and relative humidity
  • Nominal sensitivity: 0.2 cpm/pCi/L - Favorably compares to many higher end models
  • Ionization chamber detector
  • Field worthy, sturdy construction
  • No moving parts - No pumps or filters to maintain or replace
  • Annual calibration
  • Minimal setup
  • Easy tripod attachment
  • Serial port for onsite printing
  • Tamper Resistant
  • Keyed operation
  • Keypad lockout
  • Instrument motion sensor
  • Dimensions H x W x D inches: 7 x 8 x 4.5
  • Weight: 2.5 lbs.
  • Note: The EPA considers any reading under 48 hours to be invalid.

    • Manufacturers Warranty: 1 Year


    RADSTAR RS300 SAMPLE REPORT


    RADSTAR RS300 OPERATING INSTRUCTIONS

    1.0 SETTING UP THE RS300:
    A. PLUG POWER ADAPTER THAT IS MARKED " RADSTAR POWER SUPPLY" INTO ANY 110VAC OUTLET.


    B. PLUG FREE END OF POWER ADAPTER INTO LEFT SIDE OF RS300-GREEN LED SHOULD COME ON-THIS TELLS YOU THAT THE NICAD BATTERIES ARE CHARGING. POWER CORD SHOULD BE LEFT PLUGGED IN AT ALL TIMES DURING A RADON TEST TO ENSURE THAT THE BATTERIES REMAIN CHARGED. IF THERE IS NO POWER AVAILABLE, SUCH AS IN NEW CONSTRUCTION, THE UNIT MAY BE RUN FOR A TYPICAL 48HR TEST ON THE BATTERIES ALONE AS LONG AS THE UNIT HAS BEEN CHARGING WITH THE POWER ADAPTER OVER NIGHT.


    2.0 TURNING UNIT ON:


    A. INSERT KEY INTO UNIT AND TURN IT ONE CLICK TO THE RIGHT TO THE [KEYPAD ON] POSITION. THE UNIT WILL BEEP.


    3.0 SETTING UP THE RS300


    A. ERASING STORED DATA:
    PRESS AND HOLD THE [HOLD TO CLEAR] BUTTON. THERE WILL BE AN AUDIBLE TONE COMING FROM THE UNIT WHEN THIS IS DONE. RELEASE THE [HOLD TO CLEAR] BUTTON AFTER THE TONE STOPS. THERE WILL BE A SHORT “BEEP” TO SIGNIFY THAT THE MEMORY HAS BEEN ERASED. THIS IS DONE TO ERASE ANY PRIOR TEST THAT HAS BEEN STORED IN THE MEMORY SO THAT THE UNIT WILL TEST FROM THE FIRST HOUR. IF THIS IS NOT DONE, THE UNIT WILL START TESTING FROM THE HOUR THAT IT WAS SHUT OFF ON THE LAST TEST.


    4.0 MONITORING FOR RADON GAS:


    A. YOU MAY BEGIN MONITORING FOR RADON GAS BY TURNING THE KEY SWITCH TO THE [MEASURE ON] POSITION. THE KEY MAY BE REMOVED IN THIS
    POSITION TO PREVENT TAMPERING WITH THE UNIT.
    B. THE RED LED NEXT TO THE "MEASURE ON" LOGO WILL STAY ON FOR FORTY SECONDS THEN GO OUT-THIS IS A NORMAL CONDITION. EVERY THIRTY SECONDS THERE AFTER IN THAT HOUR THE UNIT WILL BEEP AND THE RED LED WILL COME ON FOR ONE SECOND AND GO OUT-THIS IS A NORMAL CONDITION. NOTE: WHEN THE KEY IS TURNED TO THE [MEASURE ON] POSITION TO START A NEW RADON TEST AND THE UNIT “BEEPS”, IT MEANS THAT THE DATA NEEDS TO BE ERASED FROM THE PRIOR TEST-SEE SECTION 3.0-A.


    5.0 OBTAINING A READING FROM THE RS300:


    A. ANY TIME DURING OR AFTER A TEST TURN THE KEYSWITCH TO [KEYPAD ON] POSITION. [NOTE]:TO CONTINUE TESTING AT ANYTIME WHEN THE KEY SWITCH HAS BEEN TURNED TO THE [KEYPAD ON] OR THE [OFF] POSITION, SIMPLY TURN THE KEY SWITCH TO [MEASURE ON] POSITION. NOTE THAT THE UNIT WILL "BEEP" TO SIGNIFY CONTINUED TESTING. NOTE: WHEN A TEST IS CONTINUED BY GOING FROM [KEYPAD ON] TO [MEASURE ON] THE HOUR THAT YOU WERE TESTING IN STARTS OVER AGAIN. ALSO NOTE THAT IF YOU TRY TO LOOK AT THE READINGS BEFORE THE FIRST HOUR IS UP THE PC OR PRINTER WILL READ: "NO DATA" .


    6.0 TRANSPORTING THE RADSTAR TO A PC OR PRINTER:


    A. IF DESIRED, YOU MAY TRANSPORT THE RADSTAR TO A PC OR PRINTER TO RETRIEVE THE DATA. TURN KEYSWITCH TO [OFF] POSITION REMOVE KEY AND DISCONNECT POWER SUPPLY. WHEN YOUR DESTINATION IS REACHED, SIMPLY INSERT KEY INTO UNIT AND TURN TO [KEYPAD ON] AND PRINT OR DOWNLOAD THE DATA.