Safety Siren Pro Series 3 Electronic Radon Gas Detector with LED Digital Readout

Free Shipping on this item!

Rated #1 Digital Readout Meter for Radon Testing by a Leading National Consumer Advocacy Group. This product is Made in the USA!

Evaluated by the U.S. Environmental Protection Agency (EPA). Meets and exceeds required performance criteria to accurately and precisely measure radon.

The Digital LED Display Radon Detector can be used for both Short and Long Term Tests. An alarm will sound when Radon Levels reach 4.0 pCi/L or higher. (This level is stated to be unsafe by the EPA)

Display range of .1 to 999.9. Shows the level of radon gas in pCi/L. Industry standard measurement unit.

This easy to use device plugs into a standard household wall outlet and allows you to continuously monitor your home for radon gas. You can easily move the detector to different floors and areas, or even test another home.

Warranty: Guaranteed to be free of defects for One-Year.

Installation

The Safety Siren Pro Series3 Radon Detector is designed to plug into a standard 120 volt household outlet using the attached power cord. The detector may be placed face up on a tabletop, counter, tip, or any flat surface where the ventilation slots will not be blocked. The detector must be kept free of dust. A proper airflow must be maintained through the detector to obtain an air sampling representative of the local enviror4enoment. Do not plug the detector into a wall socket controlled by a light switch.

How to Test

The detector measures radon gas in the air you breathe. You do not want to measure the chemical composition of objects in your home with this device. Remember, the air you breathe is the most important aspect of measuring and monitoring radon gas.

The detector should be placed in the lowest living area of the home in a location where it will not be disturbed. The audible alarm should be able to be heard from areas frequented on a daily basis. A second detector placed in a basement room rarely used, is also a good means to determine the level of radon in the home.

The location of the detector should be at lease 3 feet away from windows, doors, or any other potential openings in the exterior walls. The location of the detector should be at least 1 foot from the exterior wall and at least 20 inches from the floor. No other object should be placed within 4 inches of the detector. After taking air samples for approximately 48 hours, the initial reading will display on the screen.

Areas to avoid

Near drafts caused by heating, ventilating, air condition vents, doors, fans and windows

Near excessive heat, such as fireplaces, direct sunlight and areas of high humidity

Near TV's, computers, radios, or other electrical devices

Near furniture, curtains, or other items that may inhibit air flow through the ventilation slots of the detector

Do not place in kitchens, laundry rooms, closets or bathrooms

Do not place directly on metal, granite or slate.

Installation

The Safety Siren Pro Series3 Radon Detector is designed to plug into a standard 120 volt household outlet using the attached power cord. The detector may b placed face up on a tabletop, counter, tip, or any flat surface where the ventilation slots will not be blocked. The detector must be kept free of dust. A proper airflow must be maintained through the detector to obtain an air sampling representative of the local enviror4enoment. Do not plug the detector into a wall socket controlled by a light switch.

SPECIFICATIONS

Power Source Adapter: 120V AC, 60 Hz, 6.5 W

Input for Gas Detector: 18V DC 200mA

Sensor Voltage: 250VDC

Sensor: Ionization Chamber

Full Scale Reading: 0.0 to 999.99 pCi/L

Operating Environment: 32 Degrees F (0 Degrees C) to 104 Degrees (40 Degrees C)

Storage Environment: -4 Degrees F (-20 Degrees C) to 185 Degrees (85 Degrees C)

Audible Alarm: 85dB at 10cm - Beeps every hour if readings reach 4 pCi/L or greater. It takes at least 48 hours to get an initial reading. Alarm may be muted by user.

Dimensions: 4.7" x 3.1" x 2.1"

Manufacturers Warranty: 1 Year

If the customer deems the device defective, it must be returned to the Manufacturer, and undergo testing. Upon the results of testing; if the device is defective it will be replaced at no charge to the customer. If the device in not defective a $35.00 testing fee may apply.

This item does NOT ship to the state of Iowa